spec no: dsao4523 rev no: v.1a date: aug/01/2015 page: 1 of 6 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203015175 1.6x0.8x0.5mm bi-color surface mount led attention observe precautions for handling electrostatic discharge sensitive devices part number: APHB1608LVBDSEKJ3C blue hyper red features z 1.6mmx0.8mm smd led, 0.5mm thickness. z compatible with reflow soldering. z available in various color combination. z package: 2000pcs / reel . z moisture sensitivity level : level 3. z tinned pads for improved solderability. z low current if=2ma operating. z rohs compliant. descriptions z the blue source color devices are made with ingan light emitting diode. z the hyper red device is bas ed on light emitting diode chip made from algainp. z electrostatic discharge and power surge could damage the leds. z it is recommended to use a wrist band or anti- electrostatic gl ove when handling the leds. z all devices, equipments and machineries must be electrically grounded. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.15(0.006") unless otherwise noted. 3.the specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.the device has a single mounting surface. the device must be mounted according to the specifications.
spec no: dsao4523 rev no: v.1a date: aug/01/2015 page: 2 of 6 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203015175 selection guide notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity / luminous flux: +/-15%. * luminous intensity value is traceable to the cie127-2007 compliant national standards. absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c notes: 1. wavelength: +/-1nm. 2. forward voltage: +/-0.1v. 3. wavelength value is traceable to the cie127-2007 compliant national standards. 4. excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradat ion or premature failure. note: 1. 1/10 duty cycle, 0.1ms pulse width. part no. emitting color (material) lens type iv (mcd) [2] @ 2ma v iewing angle [1] min. typ. 2 1/2 APHB1608LVBDSEKJ3C blue (ingan) water clear 6 15 130 *6 *15 50 100 *20 *40 hyper red (algainp) symbol parameter emitting color typ. max. units test conditions peak peak wavelength blue hyper red 465 640 nm i f =2ma d [1] dominant wavelength blue hyper red 470 625 nm i f =2ma ? 1/2 spectral line half-width blue hyper red 22 20 nm i f =2ma c capacitance blue hyper red 100 27 pf v f =0v;f=1mhz v f [2] forward voltage blue hyper red 2.65 1.8 3.0 2.1 v i f =2ma i r reverse current blue hyper red 50 10 ua v r = 5v min. 2.2 1.5 parameter blue hyper red units power dissipation 90 63 mw dc forward current 30 30 ma peak forward current [1] 100 150 ma reverse voltage 5 v operating temperature -40c to +85c storage temperature -40c to +85c electrostatic dischar ge threshold (hbm) 250 3000 v
spec no: dsao4523 rev no: v.1a date: aug/01/2015 page: 3 of 6 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203015175 APHB1608LVBDSEKJ3C blue
spec no: dsao4523 rev no: v.1a date: aug/01/2015 page: 4 of 6 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203015175 hyper red
spec no: dsao4523 rev no: v.1a date: aug/01/2015 page: 5 of 6 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203015175 APHB1608LVBDSEKJ3C reflow soldering is recommended and the soldering profile is shown below. other soldering methods are not recommended as they might cause damage to the product. recommended soldering pattern (units : mm; tolerance: 0.1) reel dimension tape dimensions (units : mm)
spec no: dsao4523 rev no: v.1a date: aug/01/2015 page: 6 of 6 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203015175 packing & label specifications APHB1608LVBDSEKJ3C terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in th is document, please make sure the product is being operated within the environmental and electrical limits specified in the dat asheet. if customer usage exceeds the spec ified limits, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
|
